HP HPE0-V14 dumps - 100% Pass Guarantee!

Read the question, and then refer to the exhibit.

display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: TenGigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec -% Last 300 second output: 0 packets/sec 14 bytes/sec -% Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, -bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, -overruns, 0 aborts ?ignored, -parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, -bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, -underruns, -buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, -no carrier

A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.

The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.

From the output in the exhibit, would could be the issue?

A. The interface loopback is not set.

B. The interface link-speed and duplex are unknown.

C. The interface is administratively down.

D. The interface is configured for a PVID of VLAN 1.

A nigh school is implementing a DHCP servers to support then production environment.

They have the following requirements six rack servers, each with 1 CPU from Intel, at least 256GB of RAM. FC Dual Port HBA

HPE Nimble AF20 with 17TB useable capacity integration into their existing HPE FlexFabric 5710 and HPE SN30O0B Fibre Channel SAN switches if the customer needs more capacity in the future, they will use scale-out growth.

Which server model should you recommend to this client?

A. ProLiant DL 20 Gen10

B. ProLiant DL 325 Gen10

C. ProLiant DL 160 Gen10

D. ProLiant DL 560 Gem10

You need to update the firmware on an MSL2024 to version 26.43.51. Which HPE utility do you need to use?

A. OneView Standard

B. Smart Storage Administrator

C. Central Management Console

D. Library and Tape Tools

You are installing an HPE Nimble HF20 into a customer's existing rack.

Prior to installation, what should you consider?

A. An HPE Nimble array has left-to-right airflow

B. HPE recommends installing the HPE Nimble array at the top of the rack

C. The HPE Nimble array will require 3-phase power

D. HPE recommends racks with a depth of 1200 mm

A customer is planning an upgrade to their network infrastructure. They want to move to an open networking solution, and they want to install a network switch that supports their choice of network operating system.

Which HPE product family will meet the customer's needs?

A. Altoline

B. FlexFabric

C. Arista

D. Aruba