NS0-183 Online Practice Questions and Answers

You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.

Which tool would you use to accomplish this task?

A. Active IQ scheduled reports

B. NetAppDocs output report

C. ONTAP System Manager

D. Active IQ Config Advisor worksheet

What is the default shelf ID for disk shelves with IOM12 modules?

A. 12

B. 01

C. 10

D. 00

You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.

In this scenario, which cluster configuration is allowed with ASA controllers?

A. Add the ASA controllers to an existing 4-node cluster with NAS licenses.

B. ASA controllers can only be added to clusters that have existing SAN licenses.

C. ASA controllers can only be installed as a standalone HA pair.

D. Add the ASA controllers to an existing 10-node cluster.

You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.

In this scenario, which AutoSupport transport protocol must you use?

A. HTTP

B. SMTP

C. FTP

D. HTTPS

Click the Exhibit button.

You are setting up a new AFF A700 into a new rack at a customer's site. The customer asks you to plan for simplified future growth.

Referring to the exhibit, how would you satisfy this requirement?

A. Option 4

B. Option 2

C. Option 3

D. Option 1

Click the Exhibit button.

You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch.

Referring to the exhibit, to which port should the redundant management network be cabled?

A. 3

B. 2

C. 1

D. 4

You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.

Which statement explains this behavior?

A. You do not have network discovery enabled.

B. You do not have a static IP address.

C. You do not have IPv6 configuration set.

D. You do not have a default gateway set.

In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?

A. 2

B. 5

C. 3

D. 4

You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.

In this scenario, which network interface is needed for each SVM to register with the name service?

A. SVM data LIF

B. SVM management LIF

C. node management LIF

D. intercluster LIF

You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches.

In this scenario, which two elements would be used to complete the configuration? (Choose two.)

A. SFP+ port

B. rlogin

C. SSH

D. serial port

What are two ways to identify an AFF All SAN Array system? (Choose two.)

A. View the ONTAP System Manager system nodes.

B. View the ONTAP System Manager cluster settings.

C. Use the cluster image show CLI command.

D. Use the san config show CLI command.

You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.

How do you verify your configuration?

A. Use the storage show disk -p command.

B. Use the storage disk option show command.

C. Use the disk show -fields initiator command.

D. Use the sysconfig command.

Click the Exhibit button.

You want to add a FAS2750 HA pair to an existing 6-node cluster.

Referring to the exhibit, which action would you perform to begin adding the node?

A. Use the back command to begin the Cluster Setup wizard.

B. Reboot the node and enter maintenance mode and run the Cluster Setup wizard.

C. Use the node setup wizard and select 0a as the management interface.

D. Use the exit or quit commands then run the cluster setup command.

You are asked to add a new HA pair to an existing 2-node switchless AFF A220 cluster. You must first convert to a 2-node switched cluster using Broadcom BES-53248 cluster switches.

Which two conditions must be fulfilled before you start the migration? (Choose two.)

A. All cluster LIFs must be in the up state and on their home ports.

B. The "Enabled Switchless Cluster" option must be manually set to "false".

C. All cluster LIFs must have an MTU size of 1500.

D. The 2-node switchless configuration must be properly set up and functioning.

You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.

In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)

A. route

B. NTP

C. DNS

D. VLAN