What is the default shelf ID for disk shelves with IOM12 modules?
A. 12
B. 01
C. 10
D. 00
You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.
Which NetApp tool will verify which cluster interconnect switches support this configuration?
A. Active IQ Config Advisor
B. Interoperability Matrix Tool (IMT)
C. Hardware Universe (HWU)
D. mysupport.netapp.com site
You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center. In this scenario, which cluster configuration is allowed with ASA controllers?
A. Add the ASA controllers to an existing 4-node cluster with NAS licenses.
B. ASA controllers can only be added to clusters that have existing SAN licenses.
C. ASA controllers can only be installed as a standalone HA pair.
D. Add the ASA controllers to an existing 10-node cluster.
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?
A. BGP
B. broadcast domains
C. routing
D. IPspaces
Click the Exhibit button.
You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI. Referring to the exhibit, what must you do before you provision initial storage?
A. Configure cluster LIFs.
B. Configure protocols.
C. Configure a remote tier.
D. Configure aggregates.
You have an AFF A400 cluster that is running ONTAP 9.7 software. You are asked to set up FlexCache for NFS volumes. In this scenario, which statement is correct when implementing FlexCache?
A. A capacity license is required.
B. A subscription license is required.
C. A site license is required.
D. No license is required.
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
A. Ensure that Active IQ Config Advisor is installed.
B. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
C. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
D. Educate the onsite engineer about how to manually log support calls.
After completing a technology refresh, you need to schedule a knowledge transfer with a customer. The customer asks you to address a number of topics during the meeting. In this scenario, which two topics would be appropriate to address? (Choose two.)
A. performing database application data migrations
B. logging the customer support calls
C. accessing internal NetApp KB articles
D. registering for access to the NetApp Support site
Which three components are required when setting up a new ONTAP cluster? (Choose three.)
A. password
B. cluster management IP
C. node management IP
D. Advanced Drive Partitioning
E. intercluster IP
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster. In this scenario, which two health outputs would this command show you? (Choose two.)
A. data switch cabling
B. cluster switch cabling
C. shelf connectivity
D. node CPU utilization
You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required. Which action must be performed to ensure that the customer's requests are satisfied?
A. Perform a takeover of Node 2 to ensure that it does not run.
B. Assign all data LIFs to Node 1.
C. Assign all the partitioned disks from Node 2 to Node 1, and create a single aggregate.
D. Assign all the data partitions from Node 2 to Node 1, and create a single aggregate.
You have installed and configured a new AFF C190 cluster with ONTAP 9.7. Your customer wants you to install the latest version of ONTAP. In this scenario, what are two methods to update ONTAP? (Choose two.)
A. Use the cluster image package get and cluster image update commands.
B. Use a USB drive with the new software image and let ONTAP automatically boot.
C. Use ONTAP System Manager to download and install the new software image.
D. Use ONTAP System Manager to upload and install the new software image.
You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves. How do you verify your configuration?
A. Use the storage show disk -p command.
B. Use the storage disk option show command.
C. Use the disk show -fields initiator command.
D. Use the sysconfig command.
You want to ensure the highest path resilience and performance increase to the storage stack on your FAS8700 cluster. In this scenario, which two types of stack cabling are available to use? (Choose two.)
A. quadpath HA
B. mixed-mode
C. single path
D. multipath HA
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
A. command history
B. EMS messages
C. AutoSupport messages
D. SNMP traps