HPE6-A75 Online Practice Questions and Answers

Refer to the exhibit.

Based on the Attribute configuration shown, which statement accurately describes the status of attribute values?

A. Only the attribute values of department and memberOf can be used in role mapping policies.

B. The attribute values of department, title, memberOf, telephoneNumber, and mail are directly applied as ClearPass.

C. Only the attribute value of company can be used in role mapping policies, not the other attributes.

D. The attribute values of department and memberOf are directly applied as ClearPass roles.

E. Only the attribute values of title, telephoneNumber, and mail can be used in role mapping policies.

An administrator wants to use Airwave to manually add devices on the network. Where should the administrator perform this action?

A. in Device Setup

B. in Groups

C. in AMP Setup

D. in Devices

Refer to the exhibit.

Based on the configuration for the client's certificate private key as shown, which statements accurately describe the settings? (Select two.)

A. More bits in the private key will increase security.

B. The private key for TLS client certificates is not created.

C. The private key is stored in the ClearPass server.

D. More bits in the private key will reduce security.

E. The private key is stored in the user device.

A network administrator can set the OSPF metric-type on an AOS-Switch to Type 1 or Type 2. What is the difference?

A. A Type 2 metric marks external routes that can be advertised in NSSAs, while a Type 1 metric marks external routes that can only be advertised in normal areas.

B. A Type 2 metric assigns cost 1 to a 100 Gbps link, while a Type 1 metric assigns cost 1 to all links of 100 Mbps or higher.

C. A Type 2 metric is assigned to multiple external routes that are aggregated together, while a Type 1 metric does not permit external route aggregation.

D. A Type 2 metric stays the same as the external route is advertised, while a Type 1 metric increments with internal OSPF link costs.

A company requires AOS-Switches at the campus core. The switches:

Will act as the default gateways for several campus VLANs Must provide redundancy for their services and tolerate the loss of a link or an entire switch Must recover from the failure of one of the switches within a second or less

VRRP and MSTP are proposed to meet these requirements. What is an issue with this proposal?

A. VRRP provides redundancy against lost links but not a failed switch.

B. VRRP provides routing redundancy but not default gateway redundancy.

C. VRRP does not interoperate with MSTP.

D. VRRP takes longer than a second to fail over.

Refer to the exhibit.

An AD user's department attribute is configured as *HR". The user connects on Monday using their Windows Laptop to a switch that belongs to the Device Group HQ. Which role is assigned to the user in ClearPass?

A. Executive

B. iOS Device

C. Vendor

D. Remote Employee

E. HR Local

An administrator configures the MultiZone feature for a company network, where a mobility cluster is the primary zone and a standalone controller in the company's DMZ represents a secondary data zone. The administrator configures two AP Groups and respective VAPs for the zones on the Mobility Master (MM) in the primary zone. When the APs boot up and establish connections to both zones, the administrator notices that no data connections are established to the data zone.

What must the administrator do to fix this problem?

A. Configure the same AP Groups and VAPs on the standalone controller, and associate the MultiZone APs to both groups.

B. Configure the same AP Group in the data zone as it is in the primary zone, and configure the VAPs in the data zone.

C. Have the MultiZone APs initially boot from the standalone controller in the data zone.

D. Create different AP groups and VAPs on the Mobility Master and standalone controllers, and associate the MultiZone APs to both groups.

Refer to the exhibit.

A known unicast packet is received from Switch-1 on the standby and must be forwarded to Switch-2. How does the VSF fabric decide which port in the aggregated (ink should forward the packet?

A. The standby uses its own port in the link aggregation to forward the fabric.

B. The standby sends the packet to the commander over a VSF link, and the commander decides the correct port.

C. The standby uses the typical load sharing algorithm, and it might select either its port or the commander's port.

D. The standby selects the port on the designated forwarder for the aggregation.

Refer to the exhibit.

Traffic between the servers m Area l takes a less optimal path rather than the link associated with VLAN l OOO, subnet 10.0.0.0/30. Based on the exhibits, why is this the case?

A. The metric on the VLAN 1000 interface is too low.

B. Switch-1 and Switch-2 cannot achieve adjacency on VLAN 1000 due to mismatches.

C. OSPF routing switches choose the best intra-area routes based on Area 1 links only.

D. The link between Switch-1 and Switch-2 has gone down.

The administrator expects the AP to connect to a cluster, but the AP tails to connect. The administrator examines the configuration of an AP from apboot mode shown in the exhibit. What can the administrator determine about the configuration of the AP?

A. The AP is configured to terminate on a non-cluster Mobility Controller.

B. The AP is configured as a RAP to terminate on a stand-alone controller.

C. The AP is configured as a RAP to terminate on a Mobility Master.

D. The AP is configured to terminate on a Mobility Controller in a cluster.

An administrator needs to authenticate users connected to an ArubaOS Switch where the switch authenticates the user, assigns the firewall policies to the user, and processes some of the users' traffic. Which connection method should the administrator configure on the ArubaOS-Switch?

A. Per-user tunneled node

B. Split-tunneled mode

C. Per-port tunneled node

D. VLAN tunneled mode

An administrator supports a cluster of four Aruba Mobility Controllers (MCs) with management addresses of 10.1.100.101, 10.1.100.102, 10.1.100.103, and 10.1.202.181. The administrator accesses an AP associated with this cluster, reboots it and accesses apboot mode. The administrator executes the printenv command. Which AP parameter contains the IP addresses of the cluster members that the AP should use to connect to the cluster?

A. Noodelist

B. Servername

C. Master_ip

D. Cfg_lms

Refer to the exhibit.

Based on the Enforcement Policy configuration, when a user with Role Engineer connects to the network and the posture token assigned is Unknown, which Enforcement Profile will be applied?

A. EMPLOYEE_VLAN

B. RestrictedACL

C. Deny Access Profile

D. HR VLAN

E. Remote Employee ACL

A company has AOS-Switches deployed at sites with inexperienced IT staff. The main office network

administrators want to track if configurations change on branch switches.

What should be set up for this purpose?

A. an SNMP trap

B. an RMON alarm

C. an auto-config server

D. an lP SLA profile

Refer to the exhibit.

When configuring a Web Login Page in ClearPass Guest, the information shown is displayed. What is the Address field value 'securelogin.arubanetworks.com' used for?

A. for ClearPass to send a TACACS+ request to the NAD

B. for appending to the Web Login URL, before the page name

C. for the client to POST the user credentials to the NAD

D. for ClearPass to send a RADIUS request to the NAD

E. for appending to the Web Login URL, after the page name.