Certbus > HP > HP ATP > HP0-Y52 > HP0-Y52 Online Practice Questions and Answers

HP0-Y52 Online Practice Questions and Answers

Questions 4

Which command can a network administrator execute on an HP Comware switch to manage configuration files?

A. delete

B. startup-default

C. write file

D. write memory

Browse 116 Q&As
Questions 5

A network administrator wants to disable physical interfaces 13-24 on an HP ProVision switch. How can the administrator do this?

A. Create a named port group for interfaces 13-24. Then disable the named port group.

B. Use the interface disable command. Specify 13-24 for the ID.

C. Assign the range of interfaces to a VLAN. Then, disable the VLAN.

D. Create a named range for interfaces 13-24. Then, disable the named range.

Browse 116 Q&As
Questions 6

A company wants to implement HP Intelligent Resilient Framework (IRF) at the access layer. Which switches could they use?

A. two HP 5500 HI Series switches

B. one HP 5412R zl2 Series switch and one HP 5800 Series switch

C. one HP 5800 Series switch and one HP 5500 Series switch

D. two HP 5406R zl2 Series switches

Browse 116 Q&As
Questions 7

A network administrator configures several HP Comware switches to be part of a single Intelligent Resilient Framework (IRF) virtual device. What is correct about the domain and member IDs in this configuration?

A. The switches have different domain IDs and different member IDs.

B. The switches have the same domain ID and the same member ID.

C. The switches have the same domain ID and different member IDs.

D. The switches have different domain IDs and the same member ID.

Browse 116 Q&As
Questions 8

How does Open Shortest Path First (OSPF) help enterprises meet their high availability requirements, compared to RIP?

A. OSPF is usually easier to troubleshoot if problems occur

B. OSPF has a resilient, non-hierarchical design

C. OSPF provides faster convergence.

D. OSPF uses less CPU during routing updates

Browse 116 Q&As
Questions 9

Which ProVision configuration includes 10.0.3.0/24, which represents VLAN 30 in OSPF area 0?

A. vlan 30 ip ospf area 0

B. vlan 30 area 0

C. interface vlan 30 ip ospf area 0

D. router ospf area 0 vlan 30

Browse 116 Q&As
Questions 10

Refer to the exhibit.

Based on the output in the exhibit, which statement is correct about the spanning tree protocol running in this network?

A. Switch- is a root switch.

B. Port 2 is a designated port.

C. Port 3 is a root port.

D. Port 4 is a designated port.

Browse 116 Q&As
Questions 11

What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)?

A. With Network Segment-based discovery, network device SNMP settings must match SNMP settings on IMC. With ARP-based discovery, only ARP settings must match.

B. With Network Segment-based discovery, IMC can discover multiple devices. With ARP- based discovery, IMC can only discover one device; the administrator must re-run ARP- based discovery to discover a second device.

C. With Network Segment-based discovery, the administrator enters a range of IP addresses to discover. With ARP-based discovery, the administrator enters one seed IP address, and IMC dynamically learns more IP addresses to discover.

D. With Network Segment-based discovery, IMC can discover Layer 3 devices. With ARP- based discovery, IMC can discover only Layer 2 devices.

Browse 116 Q&As
Questions 12

A network administrator enters this command on an HP Comware switch:

save

In interactive mode, the administrator is prompted to save to a file named config.cfg and confirms the save. What is the effect of these actions?

A. The current configuration is saved to config.cfg on a TFTP server but is not used for the startup-config.

B. The startup-config, rather than the correct configuration, is saved to config.cfg on a TFTP server.

C. The current configuration is saved to config.cfg in the flash but is not used for the startup-config.

D. The current configuration is saved to config.cfg in the flash and is used for the startup- config.

Browse 116 Q&As
Questions 13

What does the traceroute command identify on an HP ProVision switch?

A. each Layer 3 device between the switch and a destination

B. the path to each router connected to the switch

C. debug output tracing entries to the routing table

D. each physical device between the switch and a destination

Browse 116 Q&As
Questions 14

A network administrator wants an HP switch to use an IP address that is always up for its Open Shortest Path First (OSPF) router ID. Which address meets this requirement?

A. An IP address configured as the global management address

B. An IP address on the interface for the default VLAN, which is typically VLAN

C. An IP address on the VLAN 1 interface

D. An IP address on a loopback interface

Browse 116 Q&As
Questions 15

Refer to the exhibit.

Examine the partial HP switch output shown in the exhibit. Based on this output, if the switch receives a packet with a destination IP address of 10.2.90.87, which entry in the routing table would the switch use to forward the packet?

A. 10.2.128.0/17

B. 10.2.0.0/17

C. 10.2.64.0/19

D. 10.2.64.0/18

Browse 116 Q&As
Questions 16

A company has a network comprised of HP Comware and ProVision switches. A network administrator purchases HP Intelligent Management Center (IMC) to manage the switches in this network. Which step must the administrator perform on the Comware switches but not on the ProVision switches?

A. Configure SNMP traps.

B. Configure VTY interface authentication.

C. Define SNMPv2 community strings or SNMPv3 groups and users.

D. Configure telnet or SSH.

Browse 116 Q&As
Questions 17

Refer to the Exhibit.

A network administrator needs to configure DHCP on SwitchA. Assume that SwitchA is an HPE Comware switch and is using the default settings for DHCP. The administrator configures the following information:

The administrator then has the DHCP client try to acquire addressing information, but the process fails. What should the administrator do to solve this problem?

A. Execute the routing command on SwitchA.

B. Execute the dhcp enable command on SwitchA.

C. Configure DHCP relay on SwitchB.

D. Enable DHCP Snooping on SwitchA.

Browse 116 Q&As
Questions 18

When adding a new member to an existing IRF domain, which of the following must you perform first?

A. Define the IRF priority.

B. Create the IRF logical port.

C. Define the IRF domain name.

D. Define the IRF member number.

Browse 116 Q&As
Exam Code: HP0-Y52
Exam Name: Applying HP FlexNetwork Fundamentals
Last Update: Mar 25, 2024
Questions: 116 Q&As

PDF

$45.99

VCE

$49.99

PDF + VCE

$59.99