You are working on a mid-range plan that spans the seasonal peak and you are evaluating the need for additional crewing. Which of the following parameters can you model to plan production with extra shift(s)?
A. Incremental production values
B. Capacity expansion with additional costs
C. Production source validity at the start of seasonal peak
D. Adjusted production interactive values
Which of these conditions must be met to create a Local Member key figure?
A. A key figure is created in the Planning Area app.
B. Use Excel Cell References in Report Editor is selected.
C. A key figure is selected in the Key Figures tab in the Microsoft Excel add-in.
D. Activate Local Member Recognition is selected.
What function would you use to configure a year-to-date calculation?
A. Rolling Aggregation
B. Last Period Aggregation
C. Cumulative Aggregation
D. Dynamic Rolling Aggregation
You want to set up demand sensing to analyze demand changes in execution or close to execution windows. Which of the following conditions must you consider during the setup? Note: There are 2 correct Answers to this question.
A. At setup test the system to run the demand sensing (full) algorithm weekly and the demand sensing (update) on a daily basis.
B. The result generates sensed demand data at the monthly time granularity for the full time horizon
C. Set up the forecast model to be executed at product-location level.
D. It is mandatory to load historical lag-based snapshot data.
Which of the following checks for master data and key figures does the Check Mode algorithm trigger? Note: There are 3 correct Answers to this question.
A. It checks whether the sourcing in the Production Source Item Master Data type exists.
B. It checks whether the location resource specified in the master data forms a cycle in the supply chain network.
C. It checks whether the heuristic detects cycles formed by nodes (such as location products) in the supply chain network.
D. It checks whether the location products specified in the master data are connected by customer sourcing rules within the supply chain network.
E. It checks whether the required planning level master data exists for a subset of input key figures.
A time profile is defined with the levels of day, technical week, week, month, quarter, and year. What condition in configuration will allow you to have a different value in the current week, versus all other buckets?
A. IF("PERIODID2" ="$$PERIODID2CU$$...)
B. IF("PERIODID5" ="$$PERIODID5CU$$...)
C. IF("PERIODID4" = "SSPERIODID4CU$$...)
D. IF("PERIODID3" ="$$PERIODID3CUSS...)
Model configuration allows the attributes of a master data type to be assigned as key figures. Which features are relevant for this type of object?
A. This object contains user-defined criteria that monitor execution of business plans.
B. This object provides a single value for a unique planning combination.
C. This type of key figure is not usually stored and it cannot be set to editable.
D. This object is not exposed to the user in planning views or modeling.
Which of the following are the key features of SAP Supply Chain Control Tower? Note: There are 2 correct Answers to this question.
A. Ability to balance demand and supply and attain financial targets
B. Ability to create a feasible plan
C. Ability to use task and case management
D. Ability to create smart alerts
Which of the following are features of the SandOP process templates? Note: There are 2 correct Answers to this question.
A. All process templates are assigned to dashboards.
B. The number of steps in a process template is the same for all implementations.
C. Each step depicted in the template can have tasks associated with it.
D. New instances of templates allow for re-use of the same processes again.
Which are the mandatory preconditions for an attribute that can be used for saving the segmentation results? Note: There are 2 correct Answers to this question.
A. It should be a non-key attribute of the master data type.
B. The length of the attribute needs to be 18 digits.
C. It belongs to a simple or compound master data type.
D. Its data type is INTEGER and its length has been specified.
Which of the following approaches could you take to reduce run times of an optimizer? Note: There are 2 correct Answers to this question.
A. Use a subnetwork ID to reduce the size of the problem.
B. Split into multiple planning areas to support weekly vs. daily planning needs.
C. Avoid using telescopic time buckets.
D. Increase the use of incremental lot size beyond the frozen horizon.
Which property of an attribute will allow it to be used as an attribute as a key figure?
A. Type TIMESTAMP
B. Type NAVCHAR
C. Type INTEGER
D. Type DECIMAL
You created a key figure and want to add calculations. Which of the following rules do you consider? Note: There are 2 correct Answers to this question.
A. All key figure calculations have calculation inputs, which can be marked as stored or calculated.
B. The calculation chain for a key figure must always result in a calculated key figure.
C. Aggregation calculations using SUM or MAX functions must be based on a higher aggregation U level.
D. Key figures can be calculated across different planning levels.
You need to create time periods for the time profile in a planning area. What should you be aware of when executing the Create Time Periods application job?
A. This application job cannot be scheduled for immediate start.
B. A time profile has to be activated so that the application job can proceed.
C. This application job can be run for multiple time profiles at once.
D. The planning area with this time profile must be activated so that the application job can proceed.
You are configuring disaggregation for the KF1 key figure. Which methods can you apply? Note: There are 3 correct Answers to this question.
A. Disaggregation according to an equal split
B. Disaggregation in batch triggered by an application job
C. An internal system-generated disaggregation
D. Proportional disaggregation by using KF2 in the expression
E. Disaggregation according to a user-defined expression