Why should you use promiscuous mode on each in-path virtual NIC for Virtual Steelhead appliance? (Select 2)
A. For LAN/WAN Virtual NICs to intercept traffic not destined for the virtual machine
B. This configuration is mandatory for traffic optimization
C. Promiscuous mode is not required
D. Only verbose mode should be configured
E. Only regular mode should be configured
When upgrading a Virtual Steelhead appliance, what steps can be taken to preserve the existing datastore?
A. When upgrading a Virtual Steelhead appliance, it is not possible to preserve the existing datastore
B. Detach the existing datastore and re-attach to the new Virtual Steelhead appliance
C. Run vMotion and move the datastore to a different ESX host before performing the upgrade and then bring it back afterwards
D. Move the existing datastore to an NFS share and move it back after the upgrade
What service needs to be allowed if you are enforcing outbound security in the Steelhead Mobile solution?
A. Rbtdebug.exe
B. Rbtmon.exe
C. Shmobile.exe
D. Rbtsport.exe
E. All of the above
What information is available in the System Snapshot files on the Steelhead Mobile Controller?
A. A copy of all memory
B. A copy of hardware registers
C. Status indicators
D. System configs and tcpdumps
E. A, B, and C
The Group ID (GID) links which two policies? (Select 2) A. Optimization
B. Acceleration
C. Installation
D. Endpoint
E. Assignment
How is peer affinity reset in the CLI for an Interceptor appliance cluster?
A. "peer affinity reset" on all Interceptors
B. "neighbor reset" on all Steelheads
C. "service restart" on all Interceptors
D. "neighbor reset" on all Interceptors
How many failover buddies can be configured for a single Interceptor?
B. 2
C. 3
D. 4
E. No limit
What parameters are required to add a new Steelhead appliance on the CMC appliance? (Select 2)
A. Hostname
B. IP address
C. Serial number
D. Sport ID
E. User name and password
What methods can the CMC appliance use to provide notification of CMC system events? (Select 3)
A. Email
B. RADIUS
C. SNMP traps
D. Syslog
The Optimization service has been disabled on a Steelhead appliance. Which of the following events occur as a result?
A. LAN and WAN interfaces stop intercepting
B. Primary interface becomes disabled
C. AUX interface becomes disabled
D. The Steelhead appliance reboots
Which of the following IP addressable interfaces can be connected for management purposes? 1) WAN 2) LAN 3) Primary 4) AUX 5) In-path
A. 1, 2, 3
B. 3, 4, 5
C. 1, 2, 4
D. 1, 2, 3, 4
E. 1, 2, 3, 4, 5
How do you clean the datastore on a Steelhead appliance? 1) > restart empty 2) > reload clean 3) # restart empty 4) # restart clean 5) (config) # reload clean
A. 1, 2
B. 2, 3
C. 4, 5
D. 3, 4, 5
E. 1, 2, 3, 4, 5
What action is taken by the Interceptor if a connection does not match a configured load balance rule and the default pool is empty?
A. The connection is forwarded for auto-discovery.
B. The connection is passed-through.
C. The connection is rejected.
D. The connection is reset.
On Steelheads, by default tcpdump:
A. captures packets with an 802.1Q tag.
B. does not capture packets with an 802.1Q tag
C. does not capture packets with an 803.3Q tag.
D. does not capture packets with an 802.11Q tag.
You see errors such as the following in the SteelHead messages log "error=SMB_SHUTDOWN_ERR_SEC_SIG_ENABLED". What do these indicate?
A. SMB signing has been detected on SMB sessions which the SteelHead attempted to optimize, but SMB signing is not configured on the SteelHeads.
B. The SteelHeads are configured to carry secure traffic over SSI and the inner channel failed to establish.
C. The optimization service encountered an error, and the SMB blade has been shut down.
D. The SteelHead encountered a kernel error and was forced to shut down.
E. The server send a secure signal to terminate an optimized SMB session.