DCPPE-200 Online Practice Questions and Answers

Refer to the exhibit.

An engineer sets up FCoE boot on their server. The server fails during post.

What needs to be added to the NIC settings/option ROM to make booting successful?

A. The WWN of the FIP snooping bridge

B. The WWN of the storage target

C. The WWN of the FC port ID

D. The WWN of the fibre channel switch

An engineer needs to connect ports 49 and 53 on an MXL to a top of rack (ToR) switch in an LACP port channel. The ToR switch has ports 46 and 60 configured in port channel 100.

Which configuration will successfully bring up the port channel on the MXL?

A. interface Port-channel 1switchportinterface range fortyGigE 0/49, fortyGigE 0/53port- channel-protocol LACPport-channel 1 mode active

B. interface Port-channel 100channel member fortyGigE 0/49, firtyGigE 0/53switchportinterface range fortyGigE 0/49, fortyGigE 0/53port-channel 100 mode active

C. interface Port-channel 100channel member fortyGigE 0/49, fortyGigE 0/53switchportinterface range fortyGigE 0/49, fortyGigE 0/60lacp mode active

D. interface Port-channel 1switchportinterface range fortyGigE 0/46, fortyGigE 0/60port- channel-protocol LACPport-channel 1 mode active

An engineer is installing two PCIe NICs into an existing VRTX chassis. Node 1 has three PCIe cards assigned to it already. After installation, the engineer is unable to assign the two new NICs to node 1.

What should the engineer do to assign the two PCIe NICs to node 1?

A. Update the CMC firmware

B. Power off the node

C. Upgrade the license

D. Reseat the NICs

Refer to the exhibit.

An engineer receives a pair of the modules shown to install into a pair of MXL switches.

Which cables does the engineer need for this module?

A. Cat6A Snagless Unshielded (UTP) Network Patch Cable

B. SFP+ to SFP+, 10GbE, Copper Twinax Direct Attach

C. QSFP+ to QSFP+, 40GbE Passive Copper Direct Attach

D. OM4 MTP Crossover FiberCable (optics required)

An engineer needs to perform hardware configuration, including RAID, on a new batch of 30 identical server nodes. OpenManage Essentials is installed, and the sever nodes have been discovered via iDRAC.

The engineer needs the most efficient way to replicate the configuration from a single configured system without losing connectivity to the iDRAC.

How should the engineer perform this task?

A. Use racadm to export an SCP with the--replaceflag, and import the SCP to the other server nodes.

B. Use racadm to export a Server Configuration Profile (SCP) with the--duplicateflag, then import the SCP to the other server nodes.

C. Complete the Getting Started for Deployment Steps; perform inventory, create a template, and deploy the created template to the server nodes.

D. Complete the Getting Started for Compliance Steps; perform inventory, create a template, and associate the server nodes to the created template.

An engineer responsible for server lifecycle management (e.g. Monitor, Update, Deploy) needs to build a monitoring strategy for a multi-vendor data center. The company has an established third party software as the monitoring and help desk system.

Which option should be used to integrate Dell Server hardware into this monitoring architecture?

A. Configure all Dell iDRACs to send alerts to the third party console. Use OME to do the rest of the lifecycle management.

B. Configure all Dell iDRACs to send alerts to the third party console. Use iDRAC to perform update and deployment.

C. Configure all Dell iDRACs to send alerts to OME to filter out wanted alerts and forward to the third party console. Build script to do the rest of the Dell server lifecycle management.

D. Configure all Dell iDRACs to send alerts to OME tofilter out wanted alerts and forward to the third party console. Use OME to do lifecycle management of Dell servers in the environment.

A VRTX server comes with two server modules. The customer requests to assign three PCIe Adapters per each server module. While performing this configuration, the engineer is unable to assign more than two PCIe Adapters per server module.

What is the cause of this issue?

A. The VRTX chassis came with a CMC Express License.

B. The CMC configuration needs to be reset to the factory defaults.

C. The VRTX chassis needs to be updated with the latest firmware.

D. This is a limitation ofVRTX chassis.

A VRTX has the following physical disks:

-8 300 GB SSDs

-10 300 GB 15,000 rpm HDDs

An engineer needs to create two virtual disks for a file server: a system volume and a data volume.

The customer wants to maximize performance of the system volume and maximize redundancy of the data

volume.

The customer also wants both virtual disks to survive one drive failure without the customer's intervention.

Which option is most appropriate to meet the requirements?

A. System: 7 SSDs in RAID 0Data: 9 HDDs in RAID 6One SSD and one HDD as dedicated hot spares for each volume

B. System: 8 SSDs in RAID 10Data: 8 HDDs in RAID 6Two HDDs as dedicated hot spares for each volume

C. System: 6 SSDs in RAID 10Data: 10 HDDs in RAID 6Two SSDs as dedicated hot spares for each volume

D. System: 7 SSDs in RAID 5Data: 9 HDDs in RAID 6One SSD and one HDD as dedicated hot spares for each volume

An engineer is in front of an FX2 chassis and notices the I/O indicator on the left ear of the chassis is flashing amber.

What are two possible causes? (Choose two.)

A. A network link has failed for one of the add-in PCIe NICs.

B. There is a problem with the chassis PCIe infrastructure.

C. A hard drive in one of the storage sleds has failed.

D. A USB key plugged into the front of the chassis has failed.

An engineer is installing a known good PCIe storage adapter in SLOT 1 of an FX2 chassis with four half height nodes. Node 1 is NOT detecting the adapter.

What must the engineer do so that node 1 can detect the adapter?

A. Power off node 1

B. Assign SLOT 1 to node 1in the CMC

C. Move the adapter to SLOT 7

D. Perform virtual reseat of the adapter

A password to the CMC root account on an M1000e server chassis has been misplaced. What should be done to restore administrative access to the CMC?

A. Reset root password using the PASSWORD_RSET jumper

B. Issue password reset from a connected blade's iDRAC

C. Call Dell tech support and ask to reset CMC password via SupportAssist

D. Access CMC through serial console and issue theenable secretcommand

An engineer configures an Alert Action in the CMC to send an email on Warning and Critical events. Chassis fan and power events are showing up as expected. Server-specific failures such as memory module failures only indicate that the server has gone into a Critical or Warning state.

What additional configuration needs to be done to be informed via email of the detailed server failure?

A. Select Server Event under Monitored Alerts Category in CMC.

B. Email Alert Action for Critical and Warning errors on all iDRACs.

C. Set Include System Event Log (SEL) option in CMC email action.

D. Enable Forward iDRAC events to CMC error log in iDRAC.

An engineer needs to configure server 1 to communicate on tagged VLANs 10, 20, and 30 and untagged VLAN 50. The server is in SLOT 1 of an FX2s chassis with two FN410s IOAs. The switches are currently set to default settings.

Which command should be entered in each IOA to perform the engineer's task?

A. interface range vlan 10, vlan 20, vlan 30, vlan 50no shutinterface TenGigabitEthernet 0/1portmode hybridswitchportvlan tagged 10,20,30vlan untagged 50

B. interface range vlan 10, vlan 20, vlan 30, vlan 50no shutinterface TenGigabitEthernet 0/1switchportvlan tagged 10,20,30default vlan 50

C. interface range vlan 10, vlan 20, vlan 30, vlan 50no shutinterface TenGigabitEthernet 0/1switchportvlan tagged 10,20,30default vlan-id 50

D. interface range vlan 10, vlan 20, vlan 30, vlan 50no shutinterface TenGigabitEthernet 0/1portmode hybridswitchportvlan tagged 10,20,30

An engineer needs to connect two MXL switches that both have SFP+ add-on module.

Which cable will complete this task?

A

A. Exhibit A

B. Exhibit B

C. Exhibit C

D. Exhibit D

An engineer is installing a server node with a quad port 1GbE NIC into SLOT 3 on a VRTX chassis with a 1GbE Pass-Through Module (PTM) in Fabric A.

During POST of this server, a message indicates that ports 3 and 4 of the NIC are being disabled. The system completes the boot process and is otherwise operational.

What is causing this message?

A. The ports haveNOTbeen enabled on the PTM.

B. The PTMonly provides eight external ports.

C. The server node needs to be in SLOT 1 to access additional ports.

D. Another server node is already using ports needed on the PTM.