7004.1 Online Practice Questions and Answers

A customer has deployed a Communication Server 1000 RIs. 7 x system at their site. Their sales department is expanding and you have been asked to add Ave new telephones with the same capabilities as the existing telephones in the department. Which programming command should you use to complete this task?

A. Move to DN

B. Move from TN

C. Copy from DN

D. Copy from TN

A customer has a Communication Server 1000 RIs. 7 x system at their site. You have been asked to add the Call Pickup feature to the ten IP telephones in the sales department. The customer wants to be sure active calls are not lost when the change are made. Which Phones Configuration feature can be enabled allowed you to ensure changes to the telephones are not transmitted to the call server until the telephone is not busy?

A. Bulk change

B. Courtesy change

C. Group change

D. Template change

Click the Exhibit button.

The local Central Office required that all calls dialed utilize dialing, however users forget to dial the NPA for local calls. Which DMI entry would be utilized to insert the NPA of 214 when a user dials 9- 774-3299?

A. DMI Table 1

B. DMI Table 2

C. DMI Table 3

D. DMI Table 4

Click the Exhibit button.

Consider the a customer's dialing plan shown in the exhibit, which detail on-net and off-net dialing requirements:

TIE trunks between Location A and Location B are currently out of service.

TIE trunks between Location B and Location D are currently out of service.

All over TIE trunks are fully functional.

Which route will a call to LOC 304-2001 take if it originates from location B?

A.

TIE BD to LocationD.

B.

TIEAB to Location A.

C.

TIE BD to LocationD,then TIE CD to Location C then TIE AC to Location A

D.

The callwill not leave the originating PBX

Which IP Peer Networking component provides the centralized call routing for Communication Server 1000 systems in an Avaya Aura network solution?

A. Call Manger

B. System manager

C. SessionBorder Controller

D. Session Manager

When attempting to program Zone Based Dialing through Element Manager, the user is unable to access

the Dialing Configuration Page.

What needs to be configured before the Dialing Configuration Page can be accessed, assuming the

ZBN_PACKAGE (420) is already installed?

A. Number Zones need to be configured

B. The CDP dialing plan needs to be programmed.

C. The ZBN_PACKAGE (420) needs to be disabled.

D. Nothing, Zone Based Dialing cannot be configured in Element Manger.

Click the Exhibit button. %

You are asked to review the existing trunk information for your customer. According to the Element Manager screen capture shown in the exhibit, which type of trunk is this?

A. Direct Inward Dial

B. Virtual Trunk

C. Recorder Announcement

D. Central Office Trunk

You are configuring a bandwidth management zone on a Communication Server 1000 RIs. 7 x Call Server.

The Call Server zones will be used for interface communications between endpoints (IP telephones and

gateways).

Which is the preferred bandwidth management strategy, assuming the network has adequate bandwidth?

A. Best Quality (BQ)

B. Best Bandwidth (BB)

C. Allocated Bandwidth (AB)

D. Best Effort (BE)

Click the Exhibit button.

Given a customer's Coordinating Dialing Plan shown in the exhibit, if a Station user at CDP Switch #2 dials 327-3249, which route list used and where will the call terminate?

A. Route List 2 will be utilized and the call will terminate at CDP Switch #2

B. Route List 10 will be utilized and the call will terminate at CDP Switch #3

C. Route List 5 will be utilized and the call will terminate at CDP Switch #2

D. Route List 1 will be utilized and the call will terminate at CDP Switch #3

A customer has deployed a Communication Server (CS) 1000 RIs. 7 x system at their site. They have asked you if the CS 1000 has a feature that can extend and ring calls to other locations. You have decided that Personal Call Assistant (PCA) will meet the customer's requirements and verified that the system is equipped with Package 398, and that it has sufficient ISM parameters. Which step must be performed first when implementing PCA?

A. Locate or configureaSuperloop for PCA

B. Enable the PCA feature for the customer

C. Configure Flexible feature codes for PCA control

D. Configure the telephone parameters to support PCA

To enabled and configured SIP on a Communication Server 1000 system, which software component on the IP Telephone Node must you enabled first using Element Manger?

A. SIPGateway

B. Media Gateway

C. Terminal Proxy Server (TPS)

D. SIP Proxy

When deploying ESA for IP telephones, a method for determining the location of the IP telephones is required. If you are deploying internally, what would one method be?

A. Deploy ESAPackage 382 (Virtual Office).

B. Deploy Location Information Services (US)

C. Deploy Discovery Manager (DM)

D. Deploy ESA Package 387 (Virtual OfficeEnhancement)

Click the Exhibit button.

Given a company's dialing plan shown in the exhibit, if a station user at the company in New York City dials 8-890-4233, what will happen to the call?

A. The Access Code of 8 will be removed and the call will complete over Route List Index# 1.

B. The call will receiveintercept treatment as indicated in the Customer Data Block (CDB) and fail to complete.

C. The NARS software will remove the Access Code and Location Code and terminate the call internally at Directory Number 4233

D. The Access Code of 8 will be removed andthe call will completeover RouteList Index #0.

An enterprise has a network with Communication Server 1000E systems running RIs 7 x IP Peer Network. For this network, when are the Digital Signal Processor (DSP) resources required?

A. when a compressedmediachannel is required without circuit switching

B. when interworkingis necessary to third-party SIP-enabled products

C. when it isnecessarytotranscode between IP and circuit-switched devices

D. wheninterworking is necessary to third-party H.323-enabled products

Given the following network characteristics:

three Communication Server 1000 RIs. 7 x systems IP Peer Networking required DN uniqueness cannot be maintained route calls using site Location Codes (LOCs)

Which type of dialing plan is recommended for this call routing scenario?

A. Flexible Numbering Plan (FNP)

B. CoordinatedDialing Plan (CDP)

C. Uniform Dialing Plan (UDP)

D. NetworkAttendantNumbering Plan